Tamco's HP6000 Series 2K Urethane Primer Sealers is a high-performance premium quality spot, panel and overall sealer and are designed for fast-drying, and provide excellent gloss holdout and Distinctness Of Image (DOI) in any topcoat system. HP6000 series sealers will provide excellent adhesion to metals, plastics and previously painted surfaces, and fill minor sand scratches and provide a uniform ground coat prior to applying Basecoat or Single Stage color. HP6000 Series Primer Sealers come in gray, black, and white and can be mixed together to offer gray scale color combinations for assisting with topcoat color hiding. Unlike other 2K sealers on the market, our sealers are made from topcoat direct to metal resins! This gives HP sealers unbeatable flow and leveling. Most sealers actually ADD to orange peel! This sealer will lay out as flat as any topcoat paint, reducing any orange peel while giving both a uniform color and added corrosion protection. We use the same 2 corrosion additives that we add to our direct to metal and direct to rust primers!
Also, since this is both a primer and sealer, you are able to spray this over bare metal, galvanize and properly prepared (sanded) aluminum when a high build primer is not needed.
HP 6000 series Primer Sealers use the same hardener as does our primers! Mix ratio is 4:1 and is ready to spray as it. Dries in 10-15 minutes – topcoat WET on WET or up to 1 hour. After 1 to 1/12 hours, sealer must sit for 4 hours or more and be sanded.
THIS WILL BE THE BEST 2k URETHANE SEALER YOU HAVE EVER USED..
Pot Life 1 hour at 75° F
4 Parts HP Series Primer to 1 Part HH-3100 Hardener
DO NOT REDUCE.. In HOT weather, 5% of HR900 retarder can be used.
Accelerator: Not recommended.
Fish Eye Eliminator: Not recommended.
Retarder: Not recommended.
Tamco Flex additive may be used at a ratio of 8:1 of uncatalyzed product....
painted surfaces thoroughly with mild detergent and water For
substrates other than unprimed plastic or fiberglass, wipe surface
with Tamco HR398 FINALWIPE
and primed areas as required.Finish sanding substrate with a minimum
of P400 DA grit or P600 grit wet. For substrates other than plastic
or fiberglass, remove sanding sludge with Final Wipe (HR398)
Manual for procedures to prepare plastic or fiberglass parts.
OEM Replacement E-Coated Parts: Clean surface thoroughly
with mild detergent and water.
clean with Tamco HR-397 Wax and Grease Remover and a scuff pad.
per accepted body shop procedures for substrate being used and final
clean with solvent wipe. Apply 1 medium coat of HP-6001 2K Sealer.
Allow 15-20 minutes flash time before topcoating.
be top-coated wet on wet after 5-10 minute flash time
TO a Maximum of 1 Hour! After 1
to 1/12 hours, sealer must sit for 4 hours or more and be sanded
Before using any Tamco products be sure to read all safety warnings
and MSDS. Please read all directions carefully.
professional use only by trained painters. Not for sale or use by
the general public.
Data & Physical Properties:
Color Multi Sprayable
Viscosity 26-30 sec. #2Z Pot
Life 2 hours Mix Ratio 4:1 Weight
Solids (RTS) 43.2% Volume Solids (RTS) 33.4%
per Gallon 8.8 lbs Color Holdout Excellent
Point 22C Solvent
Resistance Excellent Package
VOC 4.98 lbs/gal RTS VOC 3.98 lbs/gal
seconds in #2 Zahn Cup
hours at 70F
hour at 75°